LM111H DATASHEET PDF

LMH/NOPB Texas Instruments Analog Comparators Vtg Comparator datasheet, inventory, & pricing. LMH datasheet, LMH pdf, LMH data sheet, datasheet, data sheet, pdf, National Semiconductor, Voltage Comparator. LMH datasheet, LMH circuit, LMH data sheet: TI – LMN/LMN /LMN Voltage Comparator,alldatasheet, datasheet, Datasheet search site.

Author: Zolokree Kelrajas
Country: Central African Republic
Language: English (Spanish)
Genre: Business
Published (Last): 8 May 2007
Pages: 48
PDF File Size: 12.78 Mb
ePub File Size: 14.92 Mb
ISBN: 821-2-34673-494-3
Downloads: 46362
Price: Free* [*Free Regsitration Required]
Uploader: Zugis

To avoid oscillation or instability in such a usage, several. Pin connections shown on schematic diagram are for H08 package.

Certain sources datashee produce a cleaner comparator out- put waveform if a pF to pF capacitor C2 is connected directly across the input pins. Try Findchips PRO for lm A smaller capacitor is used if pin 5 is used for positive feedback as in Figure 1.

This is due to the high gain and wide bandwidth of comparators like the LM Carbon, dattasheet, and metal-film resistors have all been used successfully in comparator input circuitry. Adjustable; Input Voltage Min: The circuit of Figure 3 could be used, but it is rather awkward.

If this capacitor cannot be used, a shielding printed-circuit foil datsheet be advisable between pins 6 and 7. Both the inputs and the outputs of the LM, LM or the LM can be isolated from system ground, and the output can drive loads referred to ground, the positive supply or the negative supply. In other words there should be very little lead length or printed-circuit foil run between comparator and resistor to radiate or pick up signals.

  CATERPILLAR 308D PDF

The LM series has the same pin configuration as the iA series. Chip One Exchange 2. The positive feedback is to pin 5 one of the offset adjust- ment pins.

Search the history of over billion web pages on the Internet. To avoidof the LM See the notes dafasheet paragraph 7 below. The response time specified see definitions is lm111b a mV input step with 5 mV overdrive. Output is turned off when current is pulled from Strobe Pin.

(PDF) LM111H Datasheet download

Do Not Ground Strobe Pin. Thus, these parameters define an error band and take into account the worst-case effects of datashert gain and Rs- Note 8: Increases typical common mode slew from 7. Both the inputs and the outputs of the LM series can bespurious oscillations. The negative input voltage limit is equal to the negative supply voltage or 30V below the positive supply, whichever is less. Twisting these input leads tightly is the only second best lm111j to placing resistors close to the comparator.

When the signal source is applied through a resistive network, R sit is usually advantageous to choose an R s ‘ of substantially the same datasheet, both for DC and for dynamic AC considerations. The power supply bypass capacitors should be located within a couple inches of the LM This specification gives the range of current which must be drawn from the strobe pin to ensure the output is properly disabled.

Full text of “IC Datasheet: LM”

If pins 5 and 6 are not used, they should be shorted together. The output can also switch voltages to 50 V at currents to 50 mA. No abstract text available Text: A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.

  HEIDENHAIN EQN1325 PDF

Detector for Magnetic Transducer r. LM zero crossing detector Abstract: However, when the input signal is a voltage ramp or a slow sine wave, or if the signal source impedance is high 1 kQ to kQthe comparator may burst into oscillation near the crossing-point. This signal is centered around the nominal voltage at pin 5, so this feedback does not add to the V os of the comparator.

This is due to the high gain and wide band width of comparators like the LM Some other comparators require the power-supply bypass to be located immediately adjacent to the. If they are connected to a trim-pot, a 0.

LMH datasheet, Pinout ,application circuits Voltage Comparator – National Semiconductor

Thus, these parameters define an error band and take into account the worst-case effects of voltage gain and Rs- Note Ground foil or, posi- tive supply or negative supply foil should extend be- tween the output and the datssheet, to act as a guard.

Typical input current is 50 pA with inputs strobed off. The trim pins pins 5 and 6 act as unwanted auxiliary inputs.