LECROY 9410 MANUAL PDF

I REMOTE CONTROL MANUAL g g. II. II. II. | g. II g. II g. I li g a. Serial Number. May MODELS /14/20/24/30/ DUAL- AND QUAD-CHANNEL. 5 Manual Operation. Vertical Controls. Time-Base Controls. Probes. Bandwidth Limit. Trigger controls (Standard). Displaying Traces. Display Control and. See Remote Control Manual. 6FRSH ([SORUHU. Also via GPIB and RSC, the Scope Explorer software integrates the oscilloscope with Windows 95 and.

Author: Faegrel Voodookinos
Country: Barbados
Language: English (Spanish)
Genre: Spiritual
Published (Last): 18 January 2014
Pages: 55
PDF File Size: 14.89 Mb
ePub File Size: 17.77 Mb
ISBN: 480-4-19553-589-4
Downloads: 70439
Price: Free* [*Free Regsitration Required]
Uploader: Maushicage

Color Archiving – Copies screen in color using a wide range of digital plotters or printers. As the package is a firmware op- tion which is installed inside lecgoy oscilloscope, it eliminates the need for any external controller and is easy to retrofit. The Eproms can be removed using an IC extractor. In contrast, digital oscillo- scopes offer much better measurement precision, easy transient capture and the possibility of automation. If any parts need to be changed on the board F, the plastic front panel must be separated from the board.

Teledyne LeCroy – Product Manuals – Oscilloscopes

The current causes a voltage drop due to the internal output impedance of ,anual multiplier, up to V. Turn off all the traces, except CHI. Date, hours, minutes, seconds. Waveform data can be normalized by additive or multi- plicative constants. Check oscillators and other timing things. The address bus is internally set to hexOOOO, but the outputs are put into the high impedance state.

  LA COMMUNICATION ET LA GESTION SOLANGE CORMIER PDF

Artifact Rejection – Rejects waveforms that exceed the dynamic range of the ADC to ensure statistical va- lidity of summed average results. Hold the CRT very carefully or place soft padding under it. Broad spectrum coverage – Up to 5, spectral compo- nents. Cursors define the measurement zone. I DS Set the trigger: Triggers on similar slopes of signals narrower than a value in the range 1 0 nsec to 20 sec. For pecroy axis there is a non-linear correction amplifier, one gain and one offset lecryo amplifier, and one transconductance power amplifier to drive the current through the magnetic deflection coil.

It is advisable to perform this type of check when the scope is in a stable condition, after 20 minutes of warm up. A powerful microprocessor and a co-processor enable very rapid representation of results such as averages, integrations, exponentials and multiplications. Computations are made using bit pro- cessing that allows high accuracy, stability and repeatability.

So I guess it might be that the middle VR has gone, which could be what caused the cap to go? Search Only Within This Topic. The DC precision is 0. Top and bottom covers 4. In an lrcroy to catch transient signals, analog oscilloscopes use storage techniques that are costly and cumbersome.

The signal must be connected simultaneous- ly to two inputs. My fingers are crossed that this cap went bad and it’s the only damage. When replacing a push button, take great care to achieve good alignment, to avoid sticking when the button is used. Be careful to replace it after any work on the boards, and make sure that the two connectors are well aligned before pushing it home. The WP01 package performs digital filtering techniques that allow improved vertical resolution and sensitivity.

  ANTHILL PRO TUTORIAL PDF

Nucleoelectronica SA, 05 New Zealand: It is now possible to perform spectral analysis on repetitive and single events at an attractive price.

Operates on live waveforms with cursor readout. The number of acquisitions averaged can be selected between 2 and 1 , sweeps with the ac- cumulation automatically stopping when the number is reached. As a result, in low-noise applications, the measurement precision and dynamic range are im- proved.

LeCroy 9410 Manuals

This current controls via an amplifier the cathode voltage of the CRT. Lectoy rate enable is OFF from state 0 to state 3 included. I know it’s a long shot and you might not even be in that division For safety reasons, unplug the mains cable from the outlet without turning the scope off. Turn off all the traces except CHI.

Power spectral density PSD in dBm. Set up the DSO: Vertical resolution is 8 bits 0. The technique can be used with both single-shot and repetitive signals and provides an ideal method for smoothing transient phenomena.