IR6000 ERROR CODE PDF

These are all list of error code in Canon iR/iR more to come, i hope your machines works fine and never get error. E Main cause. fixing oil, the error code is indicated. E The rated voltage of the power supply and that of the fixing unit do not match. E Clock pulses fail to be generated. canon ir is showing an error codes E How it will solve? Your error code is for the fixing unit solve by checking the follwoing: 1. Fixing lamp.

Author: Maulabar Mazushura
Country: Morocco
Language: English (Spanish)
Genre: Medical
Published (Last): 18 January 2016
Pages: 29
PDF File Size: 10.51 Mb
ePub File Size: 3.53 Mb
ISBN: 649-5-62424-407-5
Downloads: 7438
Price: Free* [*Free Regsitration Required]
Uploader: Brajind

The fixing web length sensor PS45 is faulty. The wiring is faulty short circuit, open circuit.

Mode ofDetection The shutter closed detecting switch does not turn on when the No. The copy data controller or the remote diagnostic device is faulty. Mode ofDetection The alignment plate does not leave home position when the alignmentmotor has been driven for 2 secs. Mode ofDetection When operation starts, as many clocks errror needed do not arrivefrom the delivery motor clock sensor.

The primary charging assemblycooling fan FM2 is faulty. Erroor hopper connector is left disconnected. Mode ofDetection While the machine is in standby, the communication with the hostmachine has been interrupted for 5 secs or more. Mode ofDetection The swing guide closed detecting switch 2 does not turn on whenthe swing motor has been rotated CCW for 1 sec.

  EL RUFIAN COBARDE PDF

The puncherdriver PCB is faulty.

Canon iR5000 Service Manual: Error Codes; List Of Error Codes

The shutter closed detecting switch MS4 is faulty. The alignment motor M5S is faulty. The main thermistor TH1 has a short circuit. Mode ofDetection The puncher does not leave home position when the horizontal registrationmotor has been driven for 4 secs. Subscribe in a reader. The paper rrror platehome position sensor PI14S is faulty.

The scanner motor M3 is faulty. Main Cause The alignment plate home position sensor PI6 is faulty. The paperpush-on plate home position sensor PI14S is faulty. Mode ofDetection The stapler unit does not leave home position when the stapler shiftmotor has been driven for 4 secs. Mode ofDetection The communication between the host machine and the finisher hasbeen interrupted; this error is detected by the host machine.

Main Cause The height sensor PS1 is faulty. Mode ofDetection The stitch home position sensor front does not turn off when thestitch motor front has been rotated CW for 0.

The paperpositioning plate motor M4S is faulty. Mode ofDetection The alignment plate home position sensor does not turn on whenthe alignment motor has ir600 driven for 0.

The drum motor M1 is faulty. The fixing web has been taken up. The waste toner clock sensor MSW2 is faulty. Mode of Detection The communication between the coin vendor and the main controllerPCB has been interrupted.

  INTEL 8254 DATASHEET PDF

Main Cause The tray home position sensor PI8 is faulty.

Error Codes > Canon > iR > page 1

Mode of Detection When the host machine’s power switch is turned on, the backupdata of the EEPROM cannot be read or the data, if read, has an error. The fixing heater has an open circuit. Mode ofDetection The stapler does not leave home position when the stapler motorhas been driven for 0. The folding motor M2S is faulty. After replacing the fixing web, be sure to reset the two web counters in service mode: Main Cause The various printer board accessories are faulty.

The safety area detecting switch MS3 is faulty. The hard disk drive is faulty.

The scanner HP sensor PS39 is faulty. Main Cause The delivery motor clock sensor PI10 is faulty. The main thermistor TH1 has poor contact or an open circuit.

The finisher controller PCB is faulty. The main motor M2 is faulty.