OptiX RTN Radio Transmission System. VRC Commissioning and Configuration Guide (Web LCT). Issue, Date, HUAWEI. Huawei provides technical support resources for OptiX RTN Series Transmission Network. Access product manuals, HedEx documents, and visio stencils. Huawei provides technical support resources for OptiX RTN A Series Transmission Network. Access product manuals, HedEx documents, and visio stencils.
|Published (Last):||11 July 2005|
|PDF File Size:||7.93 Mb|
|ePub File Size:||15.92 Mb|
|Price:||Free* [*Free Regsitration Required]|
When handling a leaky battery, protect mannual the possible damage caused by the acid. At the service transmission end, the interface module packs timeslot data into ATM cells. The New Maintenance Association dialog box is displayed.
The converter reverse operation is performed by a digital-to-analog converter DAC. Transmission – – l This parameter indicates or specifies the Frequency MHz transmit frequency of the ODU, namely, the channel central frequency. It is a new version of the Internet Protocol, designed as the successor to IPv4.
Maunal 9 Repeat Step 1 through Step 8 to test all other E1 ports. Step 2 Click Query.
OptiX RTN 950
For detailed operations, see 4. BE service does not ensure any improvement in delay time, jitter, packet loss ratio, and high reliability.
If the data rtb be transmitted, certain control information is added to the data, and ftn the data and the control information are transmitted in a specified format to the physical layer. This is referred to as an IMA group. DANGER Before operating a storage battery, you must read the safety precautions carefully and be familiar with the method of connecting a storage battery. Through this method, you can ensure that the test path cover all the radio links.
Copy the configuration of the upper-layer NTP server. Select the maintenance domain in which a maintenance association needs to be created. Repeat Step 11 to create other NEs that are not created. Configure site commissioning data by using the Web 905 or configure site commissioning data by using the handheld tool.
Step 4 Click OK. Engineers also need to adjust the feed booms of the antennas so that the cross-polarization discrimination XPD meets the specified requirements.
RTN VRC01 Commissioning Guide 04 – Huawei
In other words, a header is a code segment that reflects the distribution diagram of the elements pre- specified by the sending and manuual parties. Off Indicates a power failure. The current may stop or change nanual, but it always flows in the same direction.
Thunderstorm The requirements apply only to wireless base stations or devices with antennas and feeders. Run the Internet Explorer. For details, see 2. If the switch points to “O”, the switch is turned off.
After you finish one field, press Enter to enter the next field. In addition, the U can create the NEs that are found in batches. The major commissioning steps are as follows: Step 5 Repeat Step 2 to Step 4 two to four times.
Command Conventions The command conventions that may be found huaawei this document are defined as follows. Select 4-TX Power and press Enter. For Manaul operation a hop represents a small step on the route from one main computer to another.
When touching the front panel of the board in such an environment, you must wear the protection huaei. The remote end selects signals from the two received signals. DC-return common A power system, in which the BGND of the DC return conductor is short-circuited with with ground the Mahual on the output side of the power supply cabinet and also on the line between the output of the power supply cabinet and the electric equipment.
Step 6 When you need to synchronize the NE time with the time on the NTP server, set the time synchronization mode and the related parameters. The LCAS assumes that in cases of capacity initiation, increases or decreases, the construction or destruction of the end-to-end path is the responsibility of the Network and Element Management Systems. Step 8 After the switching, query the status of the protection group that is configured on NE A.
Convention Description Boldface Buttons, menus, parameters, tabs, window, mnaual dialog titles are in boldface. Source Slot – – This parameter specifies the slot of the service huawdi. This allows Internet and other IP-based network service providers to offer different levels of service to customers.
RTN 950 V100R005C00 Commissioning Guide 02
It should show that the services are restored after transient interruption. QoS Dtn quality of service QPSK See quadrature phase shift keying quadrature phase shift A modulation method of data transmission through the conversion or modulation and keying the phase determination of the reference signals carrier.
The item may be considered as having failed; a fault has now been detected. Step 3 Click the NE Attribute[xxx] tab.
Transient contact between the core of the power cable and the conductor may generate electric arc or spark, which may cause fire or eye injury. NOTE l If the clock of an NE is selected as the working clock of the radio network, this clock should be in free- run mode and the clocks of the other NEs should be in locked mode. Huawsi main and standby radio paths are tested synchronously. Hence, you must exercise caution when using optical fibers.