HAMEG 8030 PDF

HAMEG INSTRUMENTS HM | Module: function generator; 7-Segment,5- digit LED; Band: ≤10MHz – This product is available in Transfer Multisort. F requency Range 50 mHz 10 MHz,. Output Voltage up to 10 Vpp (into 50 Ω). ☑ Waveforms: Sine Wave, Triangle, Square Wave, Pulse, DC. ☑ D istortion Factor. Funktionsgenerator HM Equipment HAMEG GmbH, Frankfurt, build ?, 4 pictures, 4 schematics, Germany, tubes, semiconductors, Service- or Lab.

Author: Arashidal Kinris
Country: New Zealand
Language: English (Spanish)
Genre: Music
Published (Last): 23 July 2007
Pages: 65
PDF File Size: 5.92 Mb
ePub File Size: 18.21 Mb
ISBN: 876-2-36682-422-8
Downloads: 72343
Price: Free* [*Free Regsitration Required]
Uploader: Shaktikinos

Adjust timebase, so that the positive pulse period of the output signal has a width of exactly 10 divisions. Vasaroltam egy hameg es szkopot.

Please select an existing parts list. Any zeroes preceding the decimal point are dropped. It is TTL compat- ible and has a duty-factor of approx. When later replacing the case, care should be taken to ensure that it properly fits under the edges of the front and rear panels. After removal of the two screws at the rear of the mod- ule, both chassis covers can be lifted.

Full text of “Hameg: hm 2”

Adjust signal height to 6 div. S 0 0 0 [T] H – Square wave signal adjustment Setting: When incor- porating it into other hamegg, the module should only be operated with the specified supply voltages. The instructions pro- vided in the operation tests in this manual can easily be carried out without using expensive test equipment.

  KUKUR KELAPA TRADISIONAL PDF

Its low frequency ranges are particularly well suited for simulating mechanical and servo techniques. The logical front-panel layout of the module ensures rapid familiarisation with the various functions. These val- ues are obtained when the generator output is terminated with 50 ohms. The Manufacturers and RS disclaim all warranties including implied warranties of merchantability or fitness for a particular purpose and are not liable for any damages arising from your use of or your inability to use the Hzmeg downloaded from this website.

The frequency ranges are adjusted in the following order: Adjust 0 for minimum overshoot or rounding, respec- tively, of the rising edge.

Hsmeg trig- ger output is short-circuit-proof and can drive several TTL inputs. In high signal volt- age ranges, it should be noted that the used terminating resistor must dissipate the corresponding effective power.

HAMEG HM 8030-6 Function Generator 10mhz

Therefore the maximum output voltage of the output socket is specified with 25Vpp. You have chosen to save the following item to a parts list:. Firstly press button – 20dB only, then both buttons dB simultaneously.

  DOXORRUBICINA MECANISMO DE ACCION PDF

If any measurement or calibration procedures are unavoidable on the opened-up instrument, these must only be carried out by qualified personnel acquainted with the danger involved.

Use a 50 ohms through-termination.

Including the amplitude control the max. Select a screen height of 6 divisions. HAMEG is not liable for consequential dam- ages.

The specified values are only obtained if the amplitude control knob is turned fully clockwise. Alternatively adjust 0 and 0, until the hqmeg value is obtained. A small circle o is now revealed on the red power button in the front centre of the mainframe.

Good luck to the repair! F – Distortion adjustment Setting: These free programs can be found on this page: The DVM should display 1 V or 0.

HM8030 Function Generator Module

Frequencies are read out on a 4 digit LED display. The capaci- tance of this isolating capacitor should be selected in that way that the frequency response of the output sig- nal is not affected over the whole frequency range of the HM unit. The required trimmer is located on hqmeg upper PCB next to the amplitude control.