This standard is issued under the fixed designation D ; the number immediately 1 This test method is under the jurisdiction of ASTM Committee D02 on. ASTM D Standard Test Method for Gage Vapor Pressure of Liquefied Petroleum (LP) Gases (LP-Gas Method). VAPOR PRESSURE ASTM D TECHNICAL SPECIFICATIONS. VAPOR PRESSURE CYLINDER UPPER CHAMBER. Stainless steel upper chamber with .

Author: Gardabei Kejar
Country: Estonia
Language: English (Spanish)
Genre: Literature
Published (Last): 4 August 2007
Pages: 215
PDF File Size: 8.6 Mb
ePub File Size: 2.1 Mb
ISBN: 178-5-48452-171-5
Downloads: 60885
Price: Free* [*Free Regsitration Required]
Uploader: Vizragore

Seta Reid Vapour Pressure Bath

Enter product namemake or model. The objective of this article is to present and discuss the different types of vapor pressure calculations available in VMGSim along with describing their calculation procedures, ranges of validity and units.

Summary of Vapor Pressure Definitions The following tables show the principal characteristics of the previously described vapor pressure definitions. The Reid Vapor Pressure is defined as the vapor pressure of a mixture as it was measured according to the experimental method depicted in the ASTM Da standard method [3]. The entire system asm immersed in a water bath at F and once equilibrium is attained the observed pressure from the measuring device is reported as the Reid Vapor Pressure.

Asgm to Active This link will always route to the current Active version of the standard. The calculation of the oil pseudo-components physical d12677 is very important since they define the computation of fugacities and equilibrium ratios that are part of the flash calculations used in vapor pressure determination.

Request prices on the required pressure gauges, thermometer, sample transfer connection and manometer. IP is a test method for determination of the air-saturated vapor pressure of crude oil. These properties are obtained from flash-based calculations that depend on the selected property package.

Koehler K (1-opening type) Reid Vapor Pressure Cylinder (ASTM D, D) | Labequip

Asm Reid Vapor Pressure is an important property of gasolines and jet fuels and it is used as a criterion for blending of products. The air saturation can be activated through the same check box as in the Reid Vapor Pressure calculation. The ASTM Da method establishes that the Reid Vapor Pressure is read from a pressure-measuring device that is attached to an ambient air filled chamber.


The ASTM D standard method follows a similar procedure than the Da method, except that the ratio of the volume of the vapor chamber to the volume of the liquid chamber is 2.

Email Us or call toll-free: Once this was done, a close match between calculated and experimental values of the distillation curve was obtained. Home Client Login Register. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Type text as it appears:: Asrm Like in the Da method, there is confusion about the units used for this property. The storage temperature is defined by the specified temperature in the stream that contains the mixture of interest.

Product tags ASTM D

Note that Nitrogen and Oxygen were added to the component list in order to be able to perform air saturation in the sample. Reid Reid Vapor Pressure Bomb.

This property is calculated based on an equation presented in the EPA publication, derived from a nomogram first published by the American Petroleum Institute APIwhich is based on the Reid Vapor Pressure Equivalent of non — pressurized vessels see definition below and the storage temperature.

Examples of these definitions are: This is no longer ast, case since VMGSim 9. Lab Equipment for Sale: The Reid vapor pressure differs from the true vapor pressure of the 1d267 due to some small sample vaporization and the presence of water vapor and air in the confined space. Now, the RVPE is obtained through a new property as shown below.

It is also a useful parameter for the estimation of losses from storage tanks during filling or draining. Consists of upper chamber and lower chamber in required 4: This option is activated through a check box that can be found in the Special Properties Unit Operation or the Refinery and Natural Gas tabs from the Material Stream as seen in the following figures.


This test method covers the Reid Vapor Pressure determination of gasoline, volatile crude oils, and other volatile petroleum products. Many problems involving hydrocarbon systems include a specification of some sort of vapor pressure measurement.

The following table shows the comparison of those values with those calculated from VMGSim: The composition in the case of a mixture also influences this equilibrium pressure.

Gas Conditioning and Processing 7 th Ed. There has been widespread confusion related to the pressure units of this property. Ast, True or Reid Vapor Pressure values are calculated for oils or its fractions, the oil pseudo-components should be modeled as accurately as possible with respect to the oil characterization data.

VMGSim calculates the vapor pressure by flashing the mixture of interest using a vapor fraction equal to zero at the temperature specified in the stream that contains the mixture.

O-ring gaskets provide tight seal between chambers and at gauge coupling. Historical Version s – view previous versions of standard. Air saturation of the sample is performed by vigorously shaking the container and returning it to the cooling bath. All examples were calculated using VMGSim 9.

Encyclopedia of Chemical Processing and Design: Oxidation Bomb for Petroleum Testing. Test Method D has been approved as a method for determination of vapor pressure of crude oil.

The vapor pressure of a mixture is commonly defined as the pressure where the first bubble of vapor is formed at a given temperature but there are other definitions based on standardized experimental measurements or correlations. The ASTM D method [1] covers the experimental procedure to obtain the vapor pressure of crude oils. General Use laboratory apparatus balances, baths, blenders, centrifuges, chart recorders, freezers, fume hoods, furnaces, glassware washers, glove boxes, mixers, moisture testing, ovens, pumps, shakers, vacuum equipment, water purification If N 2 and O 2 are not present in the component list the calculation is performed without air saturation.