Nominal dimensions and physical characteristics for copper tubes type K and L according ASTM B Standard Specification for Seamless Copper Tube for. Copper Tube Medical Gas ASTM B Type K Specification including outside diameter, wall thickness and weight. Find the most up-to-date version of ASTM B at Engineering
|Published (Last):||26 May 2007|
|PDF File Size:||8.49 Mb|
|ePub File Size:||3.85 Mb|
|Price:||Free* [*Free Regsitration Required]|
The following safety hazard caveat pertains only to the test method portion of Section dl2 of this specification.
Seamless copper bb819 for medical gas systems shall be furnished in the H58 Drawn General Purpose temper. Tension test determinations need not atsm made except when indicated by the purchaser at the time of placing the order.
The value for the Rockwell hardness number of each specimen shall be established by taking the arithmetical average of at leastthree readings.
The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Mechanical Properties The tube shall conform to the mechanical property requirements specified in Table 2 when tested in accordance with Test Methods E 18 and E 8, respectively. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but bb819 not provided as part of the standard. Squareness of Cut-fhe departure from squareness of the end of any atsm shall not exceed more than 0.
Tension test and Rockwell hardness test shall be performed to determine the tube’s tensile strength and hardness, respectively. The deviation from roundness is”measured as the difierence b891 major and minor diameters as determined at any one cross section of the tube, Inspection r The manufacturer of supplier shall inspect and make tests necessary to verify the product furnished conforms to the requierements of thus spseciflcation.
It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. A convenient method of indicating that these tests are to be made is to state that “Test Procedure T” is required zstm 4.
Types K and L tube are defined in Specification B The manufacturer of supplier shall inspect and make tests necessary to verify the product furnished conforms to the requierements of thus spseciflcation. A superscript epsilon e indicates an editorial change since the last revision or reapproval.
Copper Tube ASTM B Type K Specification
Material-The materials of manufacture shall be a cast billet of Copper Alloy UNS Cl of such purity and soundness as to be suitable for processing into the products prescribed herein. Certification When specified in the contract or purchaser order the purchaser shall be furnished certification that samples representing each lot have been tested or inspected as directed in this specification and requirements have been met.
The product shall be manufactured by such hot working necessary to convert the billet to a tubular shape and cold worked to the finished size. For the purp0se of determining conformance with the dimensional requirements specified in this specification, any measured value 0utside the specif ied limiting values for any dimensions may be cause for rejection. Mechanlcal tests-For the mechanical tests,a specimen shall be taken from each of the sample pieces selected in accordance with Mill Test Report When specified in the contract or purchase order,the manufacturer or supplier shall furnish to the purchaser a test report showing the results of tests required by this specification.
TES Certificates are available for all product upon request at the time of order. Rejection should be reported astn the producer or supplier promptly and in writing. This specification establishes the requirements for two adtm thickness schedules of specially cleaned, straight lengths of seamless copper tube, identified as Types K and L, suitable for medical gas systems. Theoretical wights for purposes of caculating weights, cross sections, and so forth, the density of the copper shall be taken as 0.
The values stated in inch-kpound units are to be regarded as standard, The values given in parentheses are mathematical v819 to Sl units,which are provided for information only and are not considered standard. The following are recommended practices lor cleaning, butthe produceris nota limited to these procedures. When specified in the contract or purchase order,the manufacturer or supplier shall furnish to the purchaser a test report showing the results of tests required by this specification.
Product: Copper Tube ASTM B819 Type K Specification
When specified in the contract or purchaser order the purchaser shall be furnished certification that samples representing each lot have been tested or inspected as directed in this specification and requirements have been met. When specified in the purchase order or contract. The product shall be separated by size,composition,and temper and prepared for shipment in such a manner as to ensure acceptance by common carrier for transportation at the l0west rate applicable and to afiord protection from the normal hazards ol transportation.
Rehearing – As a result of product reiection, the manufacturer or supplier may make claim for a retest to be ‘ conducted by the manufactuer or supplier and the purchaser.
Failur of more than on specimen to meet the specified requirements for aparticular property shall be the cause for rejection of the entire lot. Above the yield strength, the movement per minute of the testing machine head undgr load should not exceed 0. This standard does not b8819 to address all of the safety concerns, if any, associated with its use.
Eddy-current test, a nondestructive test, shall be performed as well. The n819 sof this retest shall comply with the specified requiremqnts. Materials and Manufacture Material-The materials of manufacture shall be a cast billet of Copper Alloy UNS Cl of such purity and soundness as to be suitable for processing into the products prescribed herein.
The manufacturer or supplier and the purchaser may conduct the final inspeciton simultaneously by mutual agreement. Whenever different tension test results are obtained from both full-size and from machined test specimens, the results obtained from full-size test specimens shall be used to determine conformance to the requirements of this 8b19.
DENJI ASTM B819
Limits for unnamed elements may be established by agreement between the manufacturer or supplier and the purchaser. Aetm specification number shall be shown when specified. Tension test results on material covered by this specification are not seriousle affected by variations in speed of testing. Note 2-Drawn tempertube is suitable for use with capillary solder joint fittings for brazing.
Asym tubes used for medical gas systems shall be cleaned by any of the following recommended methods: